Tynk do imitacji deski weber 25kg
    • Tynk do imitacji deski weber 25kg

    WEBER. PAS MODELINO D - model plaster for imitation board | 25kg

    zł223.40
    VAT included

    Plaster imitating the structure of the board

    Quantity
    Custom product - lead time up to 5 working days

    Ask about price

    Ask about product price

    WEBER. PAS MODELINO D - model plaster for imitation board | 25kg

    WEBER. PAS MODELINO D - model plaster for imitation board | 25kg


    Plaster imitating the structure of the board

    Please fill up below informations. System will send price for requested product immediately to email address provided.

    * Required fields

    Cancel or 

      Ability to postpone payments up to 21 days with Twisto

    Learn more...

      Fast delivery to the construction site

    Read more about deliveries...

     

    Guarantee of the lowest !!!

    Model silicone plaster Modelino D is a product with a very fine grain, in the form of a paste, ready for use. The surface can be finished in many ways depending on the tools used.

    The most important features of Modelino D plaster are:

    • resistant to algae
    • in natural raw wood colour
    • easy to shape the texture of the board
    • drawing of wood straws made with a special instrument or with the help of templates for imprinting
    • finish with acrylic sice weber.ton azure

    Application of model plaster WEBER:

    1. Preparation of the substrate:
      The substrate should be stable, load-bearing, dry, free from adhesion-reducing impurities. The surface should be even and smooth. Prime the substrate with liquid weber. prim compact. In the weber.therm DECOR insulation system, the weber.pas modelino plastering substrate is a reinforced layer made of weber KS123 adhesive and putty mortar and weber PH913 reinforcement mesh primed with weber PG225 primer. The reinforced layer should tie well and dry (about 3 days). Its thickness should not be less than 3 mm. The optimum thickness of the reinforced layer is 3 mm – 5 mm. If there are bumps, traces of the trouch should be smoothed with sandpaper. Repaint the entire surface abundantly with a coloured primer imitating weber PG225 at least 24 hours before applying the plastering mass. Priming is recommended with a brush. After the priming fluid has fully dried, on the entire plastering surface, glue the templates with a drawing of weberdeko brick made of impregnated cardboard.
      Other substrate:
      For other substrates not provided in this technical data sheet, please contact the Technical Advisory Department of WEBER
    2. Product preparation
      Decorative plastering weber.pas modelino D is supplied in ready-to-use form, it should only be thoroughly mixed using an electric agitator. If the consistency of the plaster is too dense (longer storage, high temperatures, etc.), the product can be diluted with a small amount of clean water – usually not more than 165 ml per bucket of 25 kg
    3. Executive guidelines:
      Stir the plaster with a slow-speed electric agitator. Imitation façade board: plaster is applied in two layers, the first layer with stainless steel trove to a thickness of about 1.0 mm, smoothly. After the initial binding (4-6 hours) grind the marks on the trom. Apply the second layer to a thickness of about 1.0 mm - apply to the surface, which can be worked for about 15-20 minutes. In fresh plaster, make a drawing of the hedges with a special tool, moving them on the surface, while changing the position of the stamp top - bottom. After the initial binding with a sharp tool (e.g. flat screwdriver) make a drawing of the joints between the boards from the sampler. After the plaster has been completely bonded (approx. 12 hours), sand the surface by unifying the drawing of the grains and removing the larger burrs. Paint the prepared surface with acrylic weber.ton azure once or twice, with or without a sponge, depending on the expected end result.
    4. Consumption:
      Consumption of plastering expedition on level ground (depending on the method of application): 2.0 – 2.8 kg/m²
    T_WEBER.PAS MODELINO DESKA
    28 Items

    Datasheet

    Consumption per m2
    2.0 – 2.5 kg
    Weight
    25 kg
    Thickness
    minimum thickness of the applied layer: 1.5 mm
    Density
    1.6 +/-10% g/cm3
    Application temperature
    +5°C to +25°C

    Specific links:

    You will also like the